Image-Magick on Strawberry Perl

aplonis has asked for the wisdom of the Perl Monks concerning the following question:

Replies are listed 'Best First'.
Re: Image-Magick on Strawberry Perl by syphilis (Archbishop) on Jan 27, 2015 at 02:28 UTC
It does not tell me the build for which the PPD is intended What was the actual command that you ran ? The information you seek would be contained within the PPD file that was read. Just download Image-Magick.ppd, and look at the "ARCHITECTURE NAME" entries therein. Each "ARCHITECTURE NAME" entry will specify a supported build of perl. Cheers, Rob	[reply]
Re^2: Image-Magick on Strawberry Perl by aplonis (Pilgrim) on Jan 27, 2015 at 14:11 UTC
Where might I download this from and know that it is for Strawberry Perl? I found one here... `http://www.bribes.org/perl/ppm/Image-Magick.ppd` ...but IIRC bribes.org is a source for ActiveState Perl modules, is it not? Anyhow, I'll try out Strawberry Perl 5.16 and see how that goes.	[reply] [d/l]
Re^3: Image-Magick on Strawberry Perl by syphilis (Archbishop) on Jan 27, 2015 at 14:46 UTC
...but IIRC bribes.org is a source for ActiveState Perl modules No - the Bribes' PPM packages should also work fine with any Windows build of perl that has the same $Config{archname} and version as specified in the PPD file (which you can grab at www.bribes.org/perl/ppm/Image-Magick.ppd btw). Cheers, Rob	[reply]
Re^4: Image-Magick on Strawberry Perl by Anonymous Monk on Nov 02, 2015 at 10:53 UTC
Re^5: Image-Magick on Strawberry Perl by syphilis (Archbishop) on Nov 02, 2015 at 11:30 UTC
Some notes below your chosen depth have not been shown here
Re^5: Image-Magick on Strawberry Perl by Anonymous Monk on Nov 02, 2015 at 11:01 UTC
Re^3: Image-Magick on Strawberry Perl by aplonis (Pilgrim) on Jan 27, 2015 at 14:35 UTC
SOLVED! Image-Magick installed via PPM for Strawberry Perl 5.16. So did Tk and GD-Graph.	[reply]
Re: Image-Magick on Strawberry Perl by Anonymous Monk on Jan 27, 2015 at 00:27 UTC
Have you tried doing it via `cpan`? I think this is the more common method on Strawberry Perl, and although the compilation stage can apparently be a bit tricky, Google shows a whole lot of workarounds for potential issues.	[reply] [d/l]
Re^2: Image-Magick on Strawberry Perl by aplonis (Pilgrim) on Jan 27, 2015 at 13:25 UTC
Yes, I tried cpan. But on cpan I get a different and more alarming failure. A pop-up complains "ld.exe has stopped working" and when that is acknowledged then cpan complains as below... `ld returned 255 exit status` `dmake.exe: Error code 128, while making 'blib\arch\auto\Image\Magick\Magick.xs.dll'`	[reply] [d/l] [select]
Re: Image-Magick on Strawberry Perl by Anonymous Monk on Jan 27, 2015 at 00:41 UTC
What did you try to install? Try https://metacpan.org/release/PerlMagick, try `cpanm JCRISTY/PerlMagick-6.89-1.tar.gz`	[reply] [d/l]
Re^2: Image-Magick on Strawberry Perl by aplonis (Pilgrim) on Jan 27, 2015 at 13:45 UTC
`cpanm JCRISTY/PerlMagick-6.89-1.tar.gz` ...resulted in the same error as when running the PPM. Something called `ld` stops working, and then the session ends.	[reply] [d/l] [select]
Re^2: Image-Magick on Strawberry Perl by aplonis (Pilgrim) on Jan 27, 2015 at 13:14 UTC
I was in Strawberry's own PPM, and ran "install Perl-Magick"	[reply]


We don't bite newbies here... much
	PerlMonks